Cannon-instrument CMRV-4500 Manual de usuario Pagina 19
- Pagina / 128
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
13
CANNON
®
Mini-Rotary Viscometer CMRV-4500 Instruction & Operation Manual
Version 1.1e—October, 2011 • CANNON
®
Instrument Company
2139 High Tech Road • State College, PA • 16803 • USA
Exchanger when the unit commences operation. You will be able to
observe the liquid circulating inside the reservoir from the opening at the
top of the Exchanger during normal operation. If air bubbles are consis-
tently visible in the coolant lines, add additional mixture until the Ex-
changer is full.
CAUTION
The water-antifreeze mix should be replaced annually for reliable perfor-
mance and to prevent corrosion of internal components (see Flushing
and draining the Air/Water Heat Exchanger, this chapter).
Electrical /serial connections
A/W Heat Exchanger
Plug the male end of the DC power cable into the DC POWER OUT
fitting on the rear panel of the Air/Water Heat Exchanger and turn the
locking clip clockwise to secure the connection. Attach the other end of
the cable to the receptacle labelled DC POWER at the back of the
CMRV-4500 unit (see figure, previous page). This connection provides
power to the thermoelectric cooling modules.
Insert the power cable for the Air/Water Heat Exchanger into the recep-
tacle on the Exchanger rear panel. Secure the power cable in place by
tightening the Phillips screw on the cable clamp.
Make sure the Air/Water Heat Exchanger power switch is in the OFF
position; then insert the power line cord from the Exchanger into an
appropriate power source for your unit.
Before providing mains power to the unit, check the label on the rear
panel of the Exchanger to verify that the electrical specifications for the
unit match those of the power supply.
Figure 11: CMRV rear panel
Attach the M-F three-prong connector cable from the Exchanger PUMP
outlet to the PUMP receptacle on the CMRV-4500 controller (see figures on
pages 12-13). This power connection permits CMRV-4500 control of pump
operation.
Thermistor
Insert the Lemo
®
plug from the temperature probe into the jack marked
TEMP PROBE on rear of the CMRV controller (see Figure 11). Insert
the probe tip as far as it will go into the hole marked THERMISTOR on
the rear of the CMRV-4500 chassis.
- CONTENTS 1
- CMRV-4500 2
- INTRODUCTION 7
- Instrument overview 8
- Instrument specifications 9
- Safety warnings 9
- UNPACKING AND ASSEMBLY 11
- User-Supplied Equipment 12
- CMRV-4500 APPARATUS 13
- DESCRIPTION 13
- Air/Water Heat Exchanger 15
- Front panel operations 16
- Physical placement 17
- Tubing connections 18
- Pulley-wheel installation 20
- Installation notes 21
- INSTALLATION 25
- Running the software 26
- The Instrument View window 27
- Instrument ID/Type 27
- Instrument Configuration 27
- Viewing report data 28
- Logging in 29
- Checking Instrument Settings 29
- Security options 31
- Initial security setup 32
- PREPARING FOR CMRV 35
- TESTING/CALIBRATION 35
- Inserting rotors 38
- CALIBRATING THE CMRV 39
- TEMPERATURE PROBE 39
- CALIBRATING THE 41
- CMRV CELLS 41
- Cell calibration procedure 42
- USING THE CMRV SOFTWARE 47
- Main options 48
- Analyses options 52
- Analysis types 53
- Analyses menu options 53
- Window options 54
- CMRV module menu options 55
- Profile Designer 56
- View Cell Constants 56
- Saving a configuration 57
- Calibrate Cell Constants 58
- Service menu options 60
- SUMMARY OF TEST PROCEDURE 61
- ASTM D 3829 method 62
- ASTM D 6821 method 62
- ASTM D 6896 method 63
- SAE J300 notes 63
- Delayed start option 63
- RUNNING PROFILES 65
- cover, particularly when 66
- Starting a profile 67
- Profile operation notes 68
- Displaying a profile graph 69
- Printing a profile graph 70
- MEASURING YIELD STRESS 71
- AND VISCOSITY 71
- Notes on yield stress testing 73
- Measuring apparent viscosity 73
- Notes on viscosity testing 74
- ANALYSIS CONFIGURATION 77
- Sorting analysis data 79
- Using the date filter 79
- Using the sample/error filter 80
- Resizing table columns 82
- Printing an analysis 82
- DESIGNING CUSTOMIZED 85
- PROFILES 85
- Opening the Profile Designer 86
- Interface options 87
- Managing profiles 87
- Using the Profile Editor 88
- Editing points 89
- Deleting points 89
- Cooling profile limitations 90
- Changing test parameters 91
- MRV DATA TABLE ANALYSIS 93
- ERROR LOG TABLE ANALYSIS 97
- Instrument Company 100
- EXPORT ANALYSES 101
- USING THE DATABASE 107
- Archiving old data 108
- Importing archived data 109
- WARRANTY/RETURN 111
- INFORMATION 111
- APPENDIX A — 113
- TROUBLESHOOTING 113
- APPENDIX B — 115
- REPLACEMENT PARTS LIST 115
- APPENDIX C — THERMOMETRY 117
- ASTM thermometer tables 118
- APPENDIX D — 123
- MULTI-UNIT CONFIGURATION 123
- T (continued) 127
Relacionado con productos y manuales para Instrumentos de medición Cannon-instrument CMRV-4500
(128 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales